ArmSoM Display 10 HD
The display model ArmSoM Display 10 HD1 is a ALL Oβ clock TFT LCD (Thin Film Transistor Liquid Crystal Display) module. This model is Composed of a TFT LCD panel, a driving circuit and a back light, and also has a 10.1 inch diagonally measured active display area with FHD(1200 horizontal by 1920 vertical pixel) resolution in a stripe arrangement. Display 16.7M colors by 8 bit R.G.B signal input.
General informationβ
- Outline Dimension: 143Γ228.70Γ2.25 (TYP.) mm
- Display area: 135.36(H)Γ216.58(V) mm
- Number of Pixel: 1200RGB(H)Γ1920(V) pixels
- Pixel pitch: 0.1128 (H)Γ0.1128(V) mm
- Pixel arrangement: RGB Vertical stripe
- Display mode: IPS
- Surface treatment: AG
- Back-light: White LED
- System interface: 4 lane MIPI
- NTSC: 72οΌtypeοΌ %
- Viewing Direction: ALL VIEW
- Power Consumption: TBD mW
Pinoutβ
| PIN NO | SYMBOL | Description |
|---|---|---|
| 1 | NC | OPEN |
| 2-3 | VDDIN Power SUPPLY 3.3V | |
| 4 | GND | Ground |
| 5 | RESET | Global reset signal,=VDDIN |
| 6 | NC | OPEN |
| 7 | GND | Ground |
| 8 | MIPI_TDN0 | MIPI data input. |
| 9 | MIPI_TDP0 | MIPI data input. |
| 10 | GND | Ground |
| 11 | MIPI_TDN1 | MIPI data input. |
| 12 | MIPI_TDP1 | MIPI data input. |
| 13 | GND | Ground |
| 14 | MIPI_TCN | MIPI clock input. |
| 15 | MIPI_TCP | MIPI clock input. |
| 16 | GND | Ground |
| 17 | MIPI_TDN2 | MIPI data input. |
| 18 | MIPI_TDP2 | MIPI data input. |
| 19 | GND | Ground |
| 20 | MIPI_TDN3 | MIPI data input. |
| 21 | MIPI_TDP3 | MIPI data input. |
| 22 | GND Ground | |
| 23-24 | NC | OPEN |
| 25 | GND | Ground |
| 26 | NC | OPEN |
| 27 | CABC | PWM control signal for LED driver |
| 28-29 | NC | OPEN |
| 30 | GND | Ground |
| 31-32 | LEDK | LED Cathode |
| 33-38 | NC | OPEN |
| 39-40 | LEDA | LED Anode |
1. Enable Display Overlayβ
1.1 Ubuntu22.04 image to enable display overlayβ
- Use nano to open the /boot/firmware/ubuntuEnv.txt file:
sudo nano /boot/firmware/ubuntuEnv.txt
- Find the "overlays=" keyword in the file, and add the following:
overlays=armsom-sige7-display-10hd
Shortcut keys: Ctrl + S to save, Ctrl + X to exit
After editing, restart the device to change the Overlays settings to support the Display 10 HD.
1.2 Armbian image to enable display overlayβ
- Use nano to open the /boot/armbianEnv.txt file:
sudo nano /boot/armbianEnv.txt
- Find or add the "overlays=" keyword in the file.
overlays=armsom-sige7-display-10hd
Shortcut keys: Ctrl + S to save, Ctrl + X to exit
After editing, restart the device to change the Overlays settings to support the Display 10 HD.
